I microwaved a R9 390X gaming and now my pc won't run after 3rd time

Hakaba said:
I really hope you used a microwave that is 3000W or higher. If not, what most likely happened is that the longer cook time caused the turbo encabulator magnetic seals to weaken, which led blue smoke escaping the vacuum sealed chambers. When this happens you generally have to desolder the GPU die (since it is located directly under it) and replace it with one from the same generation. I would recommend a Dyson hairdryer, it is cheaper than a hot air station but not as effective. However, it will get the job done, and make sure you get the three prong version, it is able to dissipate ESD. Unlike its two prong counterpart.

Reassembly is pretty straight forward. The only difficult part with be re-balling the GPU die. Now they make templates for some dies, which allows you to drop the lead based solder balls into the correct position. However, if you re unlucky and have to design your own, you can use a 3D printer or a 3D printing pen (a lot cheaper, but harder to deal with). After that, if you have a hot air station you can just heat it up till everything flows and seats and your done! The other way is to use a Coleman induction heater, small iron pipe (to transfer the heat to the die). But you cannot crank it to max without breaking something. So, use some painters tape to hold it down (doesn’t leave any residue behind), flip it upside down and balance it on the iron pipe, set it to mediums. Set the dyson blower to low, and just sweep back and forth on the reverse side of the socket.

That is only for the GPU die itself, since I never replaced a turbo encabulator before, it’s best to Google it and see how others have done it. I would hate for you to follow only my steps and break something.

Good Luck!
Click to expand...
You sir are a national treasure.
 
I guess we all have an idea what another Carrington Event would do to our graphic cards now...
 
200kA is a LOT of current. That switch took a serious beating.
That rig would be fun to simulate lightning strikes on hardware.
The magnetic field from those pulses could do serious damage too.
Imagine that in the hands of TechRax! :-D
 
How did I miss this thread. Great entertainment. If that was a troll it was fun... if serious also fun and I'm glad the OP was still alive to keep posting.
I admit years back I baked a ATI graphics card... got me another 6 months out of it and when it died I hit it with a somewhat more proper heat gun and got another few months out of it. (and I have to assume at this point traces have got so small that baking a card would be a terrible idea likely to fry your mother board as well)
This had to be a troll though... I mean who doesn't understand at least generally how a microwave works. lol
 
ChadD said:
How did I miss this thread. Great entertainment. If that was a troll it was fun... if serious also fun and I'm glad the OP was still alive to keep posting.
I admit years back I baked a ATI graphics card... got me another 6 months out of it and when it died I hit it with a somewhat more proper heat gun and got another few months out of it. (and I have to assume at this point traces have got so small that baking a card would be a terrible idea likely to fry your mother board as well)
This had to be a troll though... I mean who doesn't understand at least generally how a microwave works. lol
Click to expand...

I don't understand why he hasn't been banned for trolling yet.
 
Microwaved Computer

Watch that video, thats what you did to your computer, just buy a new one and learn the lesson. toaster oven or conventional over or hair dryer, those are feasable ways to reflow a card or motherboard. what you did was murder.
 
JSHamlet234 said:
Metal in microwave = high-voltage arcs. High-voltage arcs + computer parts = kaputsky. Utterly destroyed graphics card installed in motherboard = shorted out motherboard.
Click to expand...

For some reason I read this with a Mordin Solus voice 😅
 
Okay, video is not important. PS is working good now, with a paperclip.
If powering the PC all together it doesn't turn on.
Turning the case with a screwdriver bridging the power switch doesn't work.
That happens with or without the graphics card connected.
Also, is it possible to turn the PC on without the cpu 4 pins connected?
 
silent-circuit said:
Okay, video is not important. PS is working good now, with a paperclip.
If powering the PC all together it doesn't turn on.
Turning the case with a screwdriver bridging the power switch doesn't work.
That happens with or without the graphics card connected.
Also, is it possible to turn the PC on without the cpu 4 pins connected?
Click to expand...
wat?!
 
silent-circuit said:
Okay, video is not important. PS is working good now, with a paperclip.
If powering the PC all together it doesn't turn on.
Turning the case with a screwdriver bridging the power switch doesn't work.
That happens with or without the graphics card connected.
Also, is it possible to turn the PC on without the cpu 4 pins connected?
Click to expand...
I have no idea what you're talking about. Whatever you're doing, just stop.
 
silent-circuit said:
Okay, video is not important. PS is working good now, with a paperclip.
If powering the PC all together it doesn't turn on.
Turning the case with a screwdriver bridging the power switch doesn't work.
That happens with or without the graphics card connected.
Also, is it possible to turn the PC on without the cpu 4 pins connected?
Click to expand...
Are you.. lost?
 
GoldenTiger said:
No, people just need to stop reusing passwords.
Click to expand...
1638609297027.gif
 
GoldenTiger said:
It's unneeded and should therefore not be forced.
Click to expand...
It is needed. We’re in a forum in which physical goods are being sold to people and people are getting scammed. 2FA is something that shouldn’t be optional at this point for security’s sake, regardless of the strength of anyone’s password.
 
You must log in or register to reply here.
Back
Top