Recent content by Fruergaard

Update #3 So after some time working with the parts I finally got them ready for assembly. First a test fit with the Rog Apex X motherboard (~26,7 cm width). The assembly of the case (rather simple :sneaky:): With countersunk screws and T-sections to keep the case together (along with Parvum...

A little teaser: So the parts have been cut. Will see when I will have the time to cleaning, file and tap it. Also this is the motherboard that will go in my test system (Asus Maximus X Apex): And this lovely Dynatron R15 + NF-A9 will cool the I5 8600k :)

Hello everyone I'm Simon and I have been interested in SFF PCs for some years now. It started out with Unobtainable, then a SG09 mod that got replaced soon after with my own case designs. At the time there wasn't any real SFF cases so I looked into the option of using a laser cutter and assembly...

Update! So, the assembly took a little longer than expected. The CPU power position on this P8Z77-I made it a little complicated (close to the pump) and the sleeving on the 24 pin from corsair had to be removed in order to spread the cables out so they could fit in the 5mm clearance between the...

Hello So in the past year I have been doing some designing and creating some small cases in wood, acrylic, and aluminium. Some have failed, others worked great. However those that worked just wasn't good enough for me. But I think this one comes close :D It follows my last project: Project RAW...

So putting all of the TEC's together takes a little more time than expected. First apply a thin layer of Antec's Formula 7 Thermal paste to get the best transfer of heat :D And then make a sandwich of CPU coolers around it: And then connecting them all: My fingers was quite...

Okay, so some good news (and a bit of bad news). The PSU's arrived a little time ago from Antec (thanks again :D ). Three lovely Platinum PSU, two 1300W and a 1000W: Modular and OC link so two PSU's can run together :thumb: And enough power for the TEC's and stable power for the...

So, long time no see. I'm sorry for this interruption in this build log/experiment but my studies and personal situation needed some attention. And sadly I haven't been able to locate anyone with in Denmark that could and would help me making the waterblocks (had one for a few months until he...

So that last of the watercooling gear have arrived :D I would like to thanks aquatuning.de for there sponsorship of these parts along the parts for the SG09 build :D But back to the good stuff; As I said, I do no believe that radiator cooling will be my bottleneck, and here's why: One...

Sorry, my time have been limited :( But should take up speed now :D

Hi all Now with Christmas over and exams, I'm once again back to hopefully finish this build and the TEC cooler. Also Happy New Year :) This update isn't a big one, but I am in need of your help :) I'm not at big water flow engineer, so if you got any ideas for at better water block for...

Hi all Now with Christmas over and exams, I'm once again back to hopefully finish this build and the TEC cooler. Also Happy New Year :) This update isn't a big one, but I am in need of your help :) First of, I got the plexi for the window cut out. Just like the windows for my...

Don't you worry about the cost or power for these TECs Let me handle that, so you can sit back and enjoy the show :D

Hi, I'm sorry that I haven't posted for some time, but there haven't been that much to post about, since my time have been very limited, and the free time have been used to get another "chilling" project up and running with some TECs. You can se more of that here, and since the chiller will...

So I have come a bit further in with this project :D The following wasn't meant for this chiller, but for my SG09 build that was planned long ago. That's also why they have the colors that they got (not Photoshop, but spray painted). And yes, that is a Phobya External Radiator "Bench...